Bottles lampshade. How to make a bottle lamp? Production procedure. Luminaires made of glass bottles with their hands chandelier made of glass bottles with their own hands

D. hang day, friends!

Today, I decided to make a lamp from the bottle, if you are accurate, then the night light. This experience for me is completely new. I thought the lamp for a long time, but all the hands did not come out. In principle, as it turned out, nothing complicated. But I had to be patient, because Constantly had to wait. Almost at each stage of work, then the paint sued, then the shock glue. Waiting time, stretched from several hours, to several days. And otherwise, make the lamp, turned out to be an interesting and exciting occupation.

I called this work "oasis" - the desert, sand, a smile lizard, a couple of lovers and eyes ...

Usually they say - there is a sea.
But you do not have, in your eyes burning,
Perhaps I will meet now grief
In the sands of yours, so from the soul of drinking ...

The desert is fitted in the pupil
Without storm, no wind, quiet, cute ...
Your appearance is shrine for me
Well, what about him, I am so amazed ...?

Beautiful poems Anastasia Borpsova, and then, my prose

...... and again, whatever the master class would do, I had to share it, into two parts:

1. How to make a lamp;

Today will be:

How to make a lamp from the bottle

To work, I needed:

1. Glass bottle;
2. Piece of chipboard;
3. Light;
4. Cord with fork and switch;
5. Sand;
6. Shells;
7. The photo;
8. Toilet paper;
9. Acrylic paints - gold and brown;
10. PVA glue;
11. Acrylic lacquer;

As the basis of the lamp, I took a glass bottle, from under the wines.

Glass bottle

At first, I had an idea, make a lamp - "Jin in the lamp." The composition, I saw this: the sea rose a bottle of sand, through the glass is visible jinn.

I broke the entire Internet, in search of a Jinna clip, which, I would like to do. But, alas! Nothing liked. But, I met a picture that, well, right immediately, lay down on the soul. Print this picture on the usual photo paper and cut a square with rounded edges.

Picture

And glued this picture to the bottle, on the principle of reverse decoupage.

I put this picture in a cup with warm water for 10 minutes. Then I got a picture, put on the desktop, the picture down. And while wet paper, fingers, shot with a layer of white paper.

Removed the top layer

After the extra layers of paper rolled out, on the front side of the picture, it was a tassel dipped in acrylic varnish. Applying acrylic varnish, small bubbles may form, traces of which will be visible. Therefore, I tried to eliminate such bubbles immediately.

Then, put the picture to the bottle, the front side to the glass. Mocked fingers in the water and began to download paper again, thereby thinning layer. The edges of the picture, I consciously, did not even, torn. It did this in order to further, the edges of the picture were not clearly defined.

Attached a picture to the bottle.

When, as possible, thinned the layer, I took a wet napkin and everything neatly rubbed. Removed papers and traces of varnish on the glass. Leaving the picture a little to dry.

Then, brown acrylic paint, started toning a bottle. I did, it's like this: I applied to a simple kitchen sponge paint, scraped the sponge first on paper, and then the "chpokal" sponge on the bottle. I started from the picture and then throughout the bottle.

Tinging picture

Tinging a bottle

Toned in several layers. One layer will dry, nano the next.

Some moment! From tinted with a sponge, small paint bubbles are also formed. What to remove them, I just passed on them, part of the sponge, where there is little or there are no paint.

And of course, on the side of the opposite picture, left a non-colored window, in which my picture will be visible.

Run forward, I want to criticize myself. I needed to make a picture more. Because when you look straight, not very visible, the transition between the picture and paint. But if you look into the bottle on the side, this transition is very visible, and this is a marriage. Sadly ... But for the future I will be smarter.

Later, it would be a little corrected, I narrowed the window a little. But completely, I did not fix my marriage.

Not toned, bottle plot

With a bottle, while everything.

Whatever, make a lamp in the horizontal plane, I needed the foundation. For the base, I took a rectangular piece of chipboard. He asked her husband to cut a smooth rectangle and stabbing the edges. All over the surface, passed the rigid sandpaper.

Basis of chipboard

Paper Mass - Masha

Now, I needed a mass in which I could drip the bottle and which I would be able to cover with sand. Googling, stopped at Paper-Masha, whose recipe, I liked most of all. I found it in Olga Master class, a wonderful puppet master. The video of this recipe can be viewed on the YouTube channel, here is the link:

https://www.youtube.com/watch?v\u003dhoe1dx3orjk&list\u003dpl7c00c05b3ed17917&index\u003d11

1. narrowed toilet paper;
2. poured water (just to wet paper);
3. i pressed excess water;
4. in the resulting, splashing and pressed, mass of paper, added PVA glue and stirred well.

I do a papier - Masha

As a result, it turned out, here is a mass.

Mass for Papier - Masha

Before applying the mass, I abundantly smeared the chipboard with PVA glue, so that the papier - Masha was well glued to the chipboard. Gave, a little glue to grab from the chipboard and began to lay out the papier - Masha, imitating a small holly. In the middle, pressed a bottle. But, whatever stain a bottle, I thoroughly wrapped it, the food film.

Laid papier - Masha

And now, it remains to wait when Papier Masha dries. He dries for a long time, for sure.

When a lot of dried a little (about a day), I pulled out a bottle, so that the bottle is on which the bottle lies faster. But this, again, was my mistake (((. So, I did not take into account that the mass of dad-Masha will dry. The bottle stopped placing in length. It can be seen in the photo from below.

Massay, when drying, dried

I had to correct the marriage, and at the same time increased the Hollyk.

At first, the knife cut off excess, in the area of \u200b\u200bthe bottle neck. Then, again kneaded the mass from the papier-mache and laid out along the bottle, raising "sides around the bottle. And in the area of \u200b\u200bthe neck, made a groove, in which, in the future, the cord will lie.

Again laid out a lot of papier mache

And again, it began to wait when the mass dries. True, I've been waiting a little less, 5 days left for drying. But, sciences of bitter experience, the bottle left in the mass. Only, periodically, moved it, raised.

Sand decoration

When, finally, the mass dried, it began to decorated with sand.

Sand, not to buy. Slightly "robbed" a children's sandbox. Yes, they forgive me kids.))))))) Pull the sand into the deep cup and thoroughly, washed it, under running water. Mud, I will tell you, it was !!! Here you will think to think about whether to allow our children, playing in the house, publicly available sandboxes.

After the sand was washed, laid out him on the tray and put it in the oven, drying and the root. And after drying and roasted, asked him through a sieve. I needed to separate, small grain grains from large.

Then he began to decorate sand. Divaled PVA glue with acrylic varnish, approximately in the proportions of 1/1. I already used this composition when I did So it was confident in this composition.

Then, abundantly lubricated the surface with this composition and sprinkled the surface with sand, pressed his fingers. Adjusting the sand with his fingers, I blended him in the glue and at the same time smulk it to avoid tubercles. Leave to dry. Here I had to wait about 8-10 hours.

Then, squeaks the sand, gold acrylic paint. Used a wide brush. The brush in the water did not urinate, dipped only in the paint, was cutting it on paper and took place on the surface of the sand. Again let it dry, hurt relatively quickly))).

So, I made two layers.

The first two layers are small sand.

On the photo from above, it can be seen that the bottle is not tightly adjacent to the base. And I wanted to, she was recessed in the sand. Therefore, I crushed the gap. To do this, chopped a simple napkin on thin stripes and composition of glue + PVA, closed the slot (the principle is the same as the insulation of wooden window Rams, for winter).

Close the resulting gap

It did not wait for the strips dried, began to decorate them with sand, as well as the base. Adhesive sand, after drying, painted gold paint. And so three layers.

Decorated sand

Small sand, it seemed boring, so I added a layer of large sand. Acted, just like with small sand.

Decorating large sand

In forced intervals of waiting, when the sand is cooked, I made a lizard. About her, there will be the next master class.

To make a lamp, I, of course, needed a light bulb and a cord with a fork. I bought a LED light bulb (it practically does not heat up) and the finished cord, with a fork and the on / off button. Measured the length of the cord, from the switch, to the place where the light will be. And she asked her husband, soldering a light bulb to the wire.

Light bulb with cord

With the help of a thermoclaim gun, the switch was glued, the cord spent in the hollow, under the neck. And the light bulb looked into the neck.

Printed a lizard. How I did a lizard, you can see

Everything was almost ready. But I wanted, this brown-golden gamut, dilute with white pebbles and shells. Shells and large glue pebbles with a thermopystole. And small, glue on PVA + acrylic varnish.

Here, now, really, everything, work is ready. So, I did it, from the bottle, make a lamp. By the way, when, I connected the light bulb, it became clear that not all the places on the bottle were completely shattered. I wanted to fix it, but the husband stopped me in time, said that so, even more interesting. And I agreed with him.)))))

Lamp, bottle

Lamp, bottle

And yet, a little about what you can do with bottles:

• You can, for example, take a non-rational bottle with alcohol, reorganize its skin and give a man. For example, on February 23 or corporate holiday. I have such a job, MK can be viewed. By the way, this decor, removable. It can be used in the future, for bottles of similar volumes.
• Or not to throw away bottles, from under your favorite sauce, and decoupage decoupage and pep art. And use these cute bottles, under the spice. MK of this decor, you can see

Friends, if you, my master class was useful, share with friends!

Each house on the balcony or in the storage room, the garage or shed, as a rule, accumulates a large number of Plastic and glass bottles as various products consumption. Next, this trash is thrown into garbage. But you can come up with a more worthy application in everyday life, for example, make a lamp on a bottle or original chandelier. It is die by even inexperienced home masters.

In this article:

Glass bottle chandelier with their own hands

A chandeliers are used as the main source of light in almost every home or apartment. Such lighting equipment can be made independently in domestic conditions. And most importantly - such a lighting device can not be bought anywhere else, that is, it will be a beautiful exclusive product.

Consumables

• Glass bottles - the amount, the size of the blanks at will.
• Sandpaper.
• Glass cutter.
• Wire.
• Screwdriver.
• Protective facilities - mask, glasses, gloves.

Collect everyone necessary materials and tools, you can start making a homemade chandelier.

Step-by-step instruction

Step 1

It is necessary to soak the bottle for a while in the water. This will make it easy to remove the labels from it, wash off various pollution. After careful cleaning and washing, the workpiece must be enjoyed well.

Step 2.

After the bottle is dried, a cut is made at the desired level using glass cutter. To obtain as a result, an ideally smooth cut line, this procedure is recommended to produce slowly, systematically.

Important! All work with glass is necessarily carried out in the means of protection.

In the event that the houses did not turn out to be glasswise, the cut can be performed using an ordinary thread. How to do it right, there are many demonstration video on the Internet.

Step 3.

After the discharge made, the workpiece must be substitched under the crane first with hot water, then with cold. Due to the sharp heating, and then sharp cooling, the unnecessary part of the glass will drop exactly along the cut.

Step 4.

The cut line is processed using sandpaper. As a result, it should get enough smooth and smooth.

Step 5.

Taking a screwdriver in the hands, you need to disassemble the lamp, gently pull the electrical wire. Then you need to gently turn through the neck of the bottle. The lamp is going back, its performance is checked.

Step 6.

Final stage - decoration of an exclusive illuminator. On the product, ranging from the neck, the ordinary wire of any color is wound, depending on the preference of the owner or correspondence color gamma Other elements of the interior of the room.

The illuminator is ready, it remains only to mount it in place. If desired, he can give any designer species, for example, paint. The main task is that the homemade lighting device organically fit into the surrounding environment.

Recommendations! To decorate the chandelier, a glass stone is perfect, but it is worth considering that the traffic light will slightly decrease. It is better to take the stones of different shades to reproduce the effect of the game of flowers. The main thing is that the product is organically looked. For fastening glass pebbles, special adhesive is used capable of withstanding temperature differences.

The homemade illuminator will be completely ready for operation only after drying the adhesive composition, it will ensure the maximum reliability of the connection of glass parts. It will take about a day. As you can see, make a lamp from the bottle is not difficult.

Desktop lamp made of glass bottle with their own hands

For the manufacture of an unusual night lamp in household conditions, you can use the wine container a kind of form. Features of lighting will depend on the color of the selected workpiece. In the event of the original decoration, the product perfectly fit into any interior solution premises.

Consumables

• Wine glass bottle.
• Diamond drill.
• Patch.
• Shade.
• Table lamp small sizes from electric wire Sufficient length and switch.
• Defense means: mask, glasses, gloves.
• Screwdriver.
• Old towel.

Step-by-step instruction

Step 1

From the bottom on the workpiece we plan space for the hole through which the electrically conductive will be traded. At this place glue the plaster. We put on the means of protection.

Step 2.

We make a hole for an electric cord with a diamond drill. For this, the glass blank is put in a towel and start drilling a hole. This event may be needed about 30 minutes.

Step 3.

After drilling, we soak the workpiece in hot water. Outlet labels, plaster.

Step 4.

Using a screwdriver, disassemble the table lamp, carefully, so as not to damage the design elements, pull the cord.

Step 5.

In the well-done hole, we produce the electrical wire, stretch it to the sorry itself. Back collect the lamp, fix the lamp on the neck.

Desktop night light from a wine glass bottle with their own hands. Checking its performance. If there is a desire, you can additionally decorate the product using a wide variety of jewelry. For example, you can use multi-colored glass pebbles.

Recommendations! For making at home, with your own hands, any decorative lighting devices are best used wine bottles, as they differ from original forms and sizes. It provides the ability to do really exclusive interior items that can decorate any room.

You can also make a similar lamp made of plastic bottle. On the Internet you can find many options for such structures made in domestic conditions with your own hands, with detailed instructions and video.

Make a lamp of the bottle with your own hands is quite easy. Of course, it's not as easy as folded paper airplane, after all, here you have to deal with a drill, if you want to do everything beautiful, but still not so difficult, how to build a chair, for example. We describe general principle Creating a lamp from a bottle that you can customize under your own ideas. Successes!

Required materials and tools:

• drill and glass drill, or
• diamond disk for the Bulgarian (if you plan to cut off the bottom of the bottle),
• any adhesive mass that can be covered with sharp edges of the drilled hole so that they do not cut the wire,
• garland or lamp with a cartridge (depending on your goals),
• if desired, various decorations such as lampshar, etc.

Table lamp from a bottle with your own hands

How to make a lamp of a bottle with your own hands: Step by step instructions

First of all, cool the bottle: it will facilitate the drilling process.

In order to drill or cut the glass, you need to be neat and careful. If suddenly someone from your friends works with glass, you can turn to this person; Otherwise, do not be lazy to buy drill on the glass: so you will avoid unpleasant surprises In the form of a cracked or burst the surface of the bottle.

By cooling the bottle, check the point in which you plan to make a hole. Breathe patience: drill better slowly, from time to time giving a drill to cool. The same applies to the Bulgarian with a diamond disk.

Drilling a hole, you completed the most time-consuming stage of all work. Now you need to remove the sharp edges of the hole so that they do not cut the wire of the lamp. To do this, you can use sandpaper, cleaning sharp edges, or any adhesive mass - for example, plasticine. For wide holes, the adjacent rubber sealer for the crane is also suitable.

The final step remains - or insert a lamp with a base in the neck of the bottle, or fill the bottle with a garland, stretching through drilled hole wire to the outlet. If you cut off the bottom, you need to stretch the wire bulbs through the neck of the bottle, leaving the light bulb itself inside the bottle. In fact, the bottle lamp is ready. It remains only to decorate it: hang lampshade, paint, etc.

And so that you feel easier to decide on the design of your future lamp, we have collected for you 27 photos of the lamps from the bottle. Happy viewing!

Bottles unusual chandelier

Candlesticks from bottles as an exquisite decoration

The idea of \u200b\u200bdecorating the bottle do it yourself

Tender decoration of the table with their own hands

Bottle with butterflies pattern

How to make such engraving on glass, we told in the article.

Bottle and garlands lamp do it yourself

Black label label with label

The bottle can be filled with pebbles ...

... or glass. Or any other small objects that seem beautiful to you and are not prone to fire.

Green Wine Bottles Lamps

Suspended lamps that will be an interior highlight

Bottle lamp do it yourself

Suspended lamps from cognac bottles

Bottle Table Lamp with Square Exotic

Bottle chandelier, perfectly inscribed in deliberately rough bar

Idea gift chemist

Painted Bottles for Lamp

One of the main elements of the interior decor is chandelier. External species It gives the room a special highlight and style, and its lighting will create comfort, mood and harmony.

Today there are many diverse chandeliers, but not everyone can pick up something else ... do not be disappointed, because such important element decor can be created and yourself ... for example, you can make it yourself a chandelier from plastic bottles!

The process of creating a chandelier is very simple, it will require only not much time, doctrity and fantasy.

Tools and materials for the manufacture of chandeliers of plastic bottles:

- Plastic 5l. bottle;
- Plastic 2l. bottles;
- Wire;
- stationery knife or scissors;
- glue transparent;
- tweezers;
- Candle;
- Decorative decoration.

To start with 5l. Bottles neatly, smoothly cuts the neck.

Then cut off the bottom.

The height of the chandelier may be the most diverse, it depends on the preferences of each.
After, the chandelier turned out.

The dimensions of them are also dependent on the preferences of each, in this case the pieces turned out on average 3-4 cm. Thanks to a variety of color palette Plastic bottles, with a chandelier, as well as their combination, you can safely experiment ...

After the 2-liter plastic bottles turned into a non-small bunch of particles, they need to give a kind of form with a candle. For this you need to take a tweezer one plastic piece and spend it over burning candles.

As a result of deformation, a pretty curved particle will be obtained.

The lower edge of the product can also be a bit to hold over the candle, as a result of which it will also get waves, which looks very pretty!

Then, it is necessary to glue the deformed plastic pieces to glue the chandelier surface. The glue must be necessarily transparent! It is applied by stripes on a small luster area.

After that, wavy particles are attached to it.

To glue them is quite tight for a more expressive and "lush" effect. As a result, it turns out a very beautiful "air" surface ...

And when the light is turned on, they shimmer healthy!

After all pieces of plastic are glued on the craft, you need to attach a cartridge with a light bulb.

Also craft can be decorated with someone small decorative elementFor example, a plastic bottle butterfly.

That's all, the original "air" chandelier from plastic bottles is ready!

The final look of the crafts. Photo 1.

The final look of the crafts. Photo 2.

It looks great with natural lighting and sun rays, and with the (artificial) lighting, it will give the room a kind of glare and pleasant muffled light. Such an extraordinary chandelier will be an excellent addition to the interior of your room!

House design is a complex and responsible task, to cope with which you can independently. The peculiarity is that some interior items can be created with their own hands. So, the lamps are essential interior objects that are used to illuminate the room as a whole or separate zone. The store presents a wide range of such products. But there are master classes how to make a lamp do it yourself from the bottle. And now we will show you! :)

How to make a chandelier (master class!)

The main lighting device of the house is the chandelier. It is possible to make it from a conventional glass bottle. The main thing is that it will be exclusive.

To create such beauty you will need:

• bottles (size and quantity depends on host preferences);
• protective equipment (glasses, mask and gloves);
• glass cutter and sandpaper;
• screwdriver and wire.

Having the necessary tools and materials at hand, you can proceed to the direct fabrication of the chandelier:

1. Soak a bottle in water. This will make it easy to eliminate labels and trash. After cleaning, the container must be carefully dried.

My bottles and clean from labels

2. Make a bottle cut. The glass cutter is installed at the required level. Cut is carried out in slower, which will allow you to get a flat line of cut. Working with cutter is needed exclusively in protective clothing. If there is no required toolThe glass bottle cut is easily performed by thread. On the video below, it is clearly demonstrated.

3. Now bottle is substituted under the crane. Turn on hot water and keep the workpiece under it. Hot water Alternate with cold. As a result of sudden temperature drops, an unnecessary piece will disappear exactly along the line of the cut.

4. The cutting place is processed Emery paper. The slice should be smooth and smooth.

5. With a screwdriver, a lamp is disassembled. The wire must be carefully drawn and skip through the neck, assemble the lamp back and check it in operation.

6. It remains only to decorate the lighting device. This uses the usual wire. Starting from the neck, wound it on the bottle. For this, any material is used. It can be the usual black or colored wire.

Suspension on the chandelier is ready. It remains only to install it. If desired, the product can be painted and give any design. The main thing is that it is organically combined with the interior of the room.

A good solution will be the use of glass stone. It should be borne in mind that the light permeability of the product will slightly decrease. For decorating, a stone is used for various shades. You can combine a few shades. The main thing is that the lamp looked organically.

Stones are attached to the glass with glue. The lamp can only be used after its complete drying. It will take no more than a day. Complete drying of glue will provide a reliable clutch of stone with a surface. It is better to use a glue composition that can withstand temperature differences.

Table lamp (master class!)

A glass bottle will become the perfect material for creating a desktop lamp in a bedroom or living room.

To do this, you will need:

• bottle of appropriate shape and size;
• diamond drill;
• shade;
• screwdriver;
• means of protection;
• old towel;
• patch;
• Wire with carton.

Production of a lamp from a bottle with own hands is carried out in the following sequence:

1. Stand opening on the workpiece through which the wire will pass. To stick the plaster.
2. Bottle lay on an old towel and drill a hole under the wire. Drilling is carried out using a diamond drill. Work is carried out in the means of protection.
3. Finished bottle to soak in water and eliminate all stickers and pollution.
4. The wire is passed into the hole and stretches to the neck. At the outlet, it connects to the cartridge.
5. Secure the cartridge and lampshade on the neck.

Homemade table lamp made of glass bottle ready. It remains only to check it in work. If desired, the product can be decorated and decorated. For this use various technologies and materials. Original decision Glass stones will become, especially if the room is installed glass chandelierManufactured using the previous master class.

Now you know how to make a bottle lamp. Most often, bottles are used for the manufacture of such devices. They have different sizes and shapes. This allows you to build an exclusive item that will be decorated for the room.

Plastic lamp (MK)

Plastic bottles are widely used for the manufacture of the lamp. The peculiarity of such a product is the simplicity of attachment and ease. Perform such a lamp from plastic bottles with your own hands. Today there are several technologies with which the original lighting. Let's start with a simple method.

For the manufacture of the lamp will take:

• 5-liter plastic bottle;
• stationery knife;
• glue;
• disposable spoons.

Manufacturing process:

1. Using a knife cuts bottom. The slice should be smooth. In the future, this will make it easier to work with decoration.

2. Pens cut off spoons. Using glue, convex parts are glued to the workpiece. You need to start with the neck. Each subsequent row should go to the previous one.